The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
We have discovered this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and believe it made good sense to talk about it with you here.
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is also a moderately hard task. If the old tub is easily obtainable, the task can relocate easily; if you need to open a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as set in the new one. Ensure you have certified on your own for the job and are comfortable attempting it. As opposed to hiring a contractor to take control of a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you might require an expert plumber to make tube links.
This short article will certainly assist you set up a new tub in your restroom if you have actually currently gotten a new tub and do not require to transform the setup of your previous supply of water pipelines.
Your tools and product checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the restricted accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Protect the faucet in place with the supplier provided backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the tub in the required placement. The wooden boards are useful in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water and also examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the bathtub has actually been made use of at least once as this will certainly settle it into its last setting.
Planning for the Setup
To start with, the supporting structure provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about problems with moisture and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to allow for the activity experienced when the bathtub remains in use. The sealer can split fairly very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting about Tools You Need to Install a New Bathtub while browsing the search engines. Appreciated our article? Please share it. Help other people check it out. Thank you for going through it.
Expertise at your service. Report this page